What is the making nail polish dry faster correct procedure for making nail polish？

Many people will apply nail polish, and different manicurists use different methods when making nails. Therefore, the works presented by manicurists must be different. Many people still can’t use nail polish. Many people want to learn how to make their hands more attractive. The correct method of making nail polish is not as difficult as they think.did julep stop making nail polish What is the correct procedure for making nail polish? Now let’s take a look.

1.Modification type

First, use a standard file to trim the nail to the designed shape. Later, note that the fingertips under the nail tip should be removed with a sponge file to prevent the nail polish from sticking to the fingertips and causing the nail tip to rise and fall off quickly. Trimming dead skin: first push the excess dead skin on the nail edge with the dead skin steel, and then trim it with the dead skin scissors to prevent the nail polish from sticking to the dead skin or meat and causing the back edge to rise and fall off quickly. Polish the nail surface and clean it: then rub the rough surface with a sponge and polish the nail surface, focusing on the circle around the nail and the nail tip. In case of falling nails or soft and thin nails, you must use a standard file to carve and polish them carefully. Note: this step can be completed quickly without affecting the quality, because: in addition to shaping, the nail surface needs to be carved and polished carefully. The finger scraps can be removed by gently removing the area (the dead skin can be repaired. Some girls have less dead skin on the nail margin, so they can be repaired simply or not.nail polish base for making nail polish Just gently push the dead skin upward for the next step. The finger scraps can also be removed by gently removing the area.

2. Apply bond

Correct operation process of nail polish adhesive the binder is aqueous. Do not take too much to avoid flowing or drying. The bond only needs to be applied around the edge of the nail and the nail tip, because the focus is around the nail tip, which is also easy to fall off. In the process of nail removal, firstly, how to start making nail polish it is easier to remove. Secondly, it will not cause damage to the surface of the customer’s nails. Finally,make nail polish liquid again it is necessary to pay attention to the edge wrapping without lighting. Note: this step can be omitted when the speed is increased, because some brands of cement and primer are two and one, so only primer can be applied.

3.Apply primer

Correct operation process of nail polish adhesive: the primer shall be taken in full amount. Do not apply too thin around the edge. If it is too thin, it will lose support, resulting in massive fragmentation and falling off from the edge like a pancake. It is recommended to use the half application method from bottom to top (first apply the bottom half of the nail, and then apply the whole face upwards, so that the color saturation is stronger and the upper and lower parts are more uniform). Finally, pay attention to the edge wrapping. The LED light must last for 1 minute and the UV light must last for 3 minutes. (uniform headlamp)

4. Apply nail polish

Correct operation process of nail polish glue nail polish is applied normally, and the amount is normal. It is not necessary to apply too much. Too much will lead to uneven application. Similarly, the edges should be piled around a little more, so that the edges will not be blurred and more solid. To prevent lumps from falling. Finally, pay attention to edging, LED lighting for 30 seconds, UV lighting for 1 minute. (uniform lighting) then apply the same as above for the second time, and the color saturation will be enhanced.

5. Apply seal coat

Correct operation process of nail polish adhesive: the sealing layer shall be full, the edge shall not be painted too thin, and the color glue shall be completely covered. The nail surface shall be coated. Finally, pay attention to the edge wrapping. The LED light must be 1 minute, and the UV light must be 3 minutes. (uniform lighting) in addition, remember that if the nail of the guest is very thin, it is recommended to apply primer for 3 times more and apply color glue after reinforcement. Never apply more sealing layer，apps for making nail polish.

First It is not easy to fall off after reinforcement.making nail polish brighter.

Second If you apply the seal coat for 3 times, it will be very troublesome to remove, because the primer density of all nail polish adhesives is not as high as that of the seal coat, so the primer is easy to remove. The above is the standard operation process of nail polish,

This is the best top coat and color gel I have used for many years.gel top and base coat with regular polish. https://gelnailpolish.cn

Phone No.:+8615999362947

Whatsapp:+8615999362947